ASTM A255 PDF

Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.

Author: Kigazragore Mikajar
Country: Haiti
Language: English (Spanish)
Genre: Science
Published (Last): 28 July 2008
Pages: 10
PDF File Size: 12.65 Mb
ePub File Size: 5.2 Mb
ISBN: 584-4-39898-365-4
Downloads: 97390
Price: Free* [*Free Regsitration Required]
Uploader: Gukus

In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which satm to a given hardness level. Carbon and Sulfur Analysis. Proceed to Checkout Continue Shopping.

As the voice of the U. The sample is then brought back up to austenitizing temperature as specified for alloy, and end quenched with a specialized holder for the end quench to occur. These curves give High and Low values which material should fall into.

This may be accomplished by heating the specimen in a vertical position in a container with an easily removable cover containing a layer of cast-iron chips with the bottom face of the specimen resting on the chips. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

The support for the specimen shall be dry at the beginning of each test.

Current edition approved March 10, Wash the sample in hot water. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. This testing is indented for determining the hardenability of steels.

The small adtm specimen inserted in the sheath, and the sheath warmed to a temperature above the melting point of the Woods metal. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations asmt to use.

  ANADARA TUBERCULOSA PDF

Carbon multiplying factor 5 0. Boron factor 5 1. Active view current version of standard. A tank of sufficient capacity to maintain the water temperature requirements of 6. It is the responsibility of the user of this standard to establish appropriate safety astm a health practices and determine the applicability of regulatory limitations prior to use. The variations between spacings should be even smaller. A2555 is important that no vertical movement be allowed when the major load is applied.

Historical Version s – view previous versions of standard Translated Version s: Link to Active This link will always route to the current Active version of the standard. Then heat the assembly and quench in accordance with 6. Rockwell or Superficial Hardness. The astm a given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

If the retest also has greater than 4 HRC points spread, a new specimen should be tested. Index of Hardenability 8. This standard does not purport to address all of the safety concerns, if any, associated with its use. The use of these equations to plot curves may result in random in?

The test specimen shall be 1.

G2MT Laboratories

Asmt curves give High and Low values which material should fall into. The values given in parentheses are for information only. We have no amendments or corrections for this standard. The mold may also be used to form a 1.

The test consists of water quenching one end of a cylindrical test specimen 1. For comparison of this test method to others, or for steel compositions outside the mentioned grades, the user ast refer to other articles concerned with calculating hardenability.

  BARTLEBY LE SCRIBE MELVILLE PDF

Then make Rockwell hardness measurements on the C scale on the specimen as prescribed in 6. It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench.

ASTM A – 02 Standard Test Method for Determining Hardenability of Steel

The values given in parentheses are for information only. When hardness readings are taken on two or more? CarbonGrain Mn Size 7 0. The two test methods include the quantitative end-quench or Jominy Test and 2a55 method for calculating the hardenability of steel a25 the chemical composition based on the original astm a by M.

ASTM A255 PDF DOWNLOAD

It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. The anvil must be constructed to move the test specimen past the penetrator in accurate steps of 1? Wash in aa255 water. Etch in solution No. The time between removal of the specimen from the furnace and the beginning of the quench should not be more than 5 s.

The sample shall be held at the temperature listed in Table 1 for 1 h and cooled in air.

If the standard hardenability curve is needed, then the insert test specimen shown in Fig. Standards Subsctiption may be the perfect solution. The positioning of the indenter should be checked with sufficient frequency to provide assurance that accuracy requirements are being met. Plotting Test Results 7.