ASTM D5511 PDF

ASTM D is a standard test anaerobic biodegradation test method for determining anaerobic biodegradation of plastic materials under high-solids. ASTM D Standard Test Method. D Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under. High-Solids. ASTM D Significance and Use. Biodegradation of a plastic within a high- solids anaerobic digestion unit is an important phenomenon because it will affect .

Author: Dosida Taurg
Country: El Salvador
Language: English (Spanish)
Genre: Finance
Published (Last): 10 December 2006
Pages: 444
PDF File Size: 15.15 Mb
ePub File Size: 15.80 Mb
ISBN: 254-8-79513-260-7
Downloads: 89116
Price: Free* [*Free Regsitration Required]
Uploader: Tuzil

ASTM D5511 – Anaerobic Biodegradation

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Placing the sample materials in an inoculum derived from anaerobic digesters operating on household waste.

Furthermore, results shall not be extrapolated past the actual duration of the test.

Reports shall clearly state the percentage of net gaseous carbon generation for both the d551 and reference samples at the completion of the test. Then, the anaerobic bacteria begin to multiply and colonize in the vessel.

Note 1—This test method is equivalent to ISO Work Item s – proposed revisions of this standard. The test is allowed to run for as long as desired. This test method also resembles other anaerobic conditions where the gas generated is recovered and biogas production is actively promoted by inoculation for example, codeposition of anaerobic sewage sludge, anaerobic leachate recirculationmoisture control for example, leachate recirculationand temperature control for example, short-term injection of oxygen, heating of recirculated leachate 5, 6, 7.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. They are kept within strict temperature and moisture tolerances. The testing process includes: Three vessels are used for each sample, and one negative control and one positive control are prepared as well. Link to Active This link will always route to the current Active version of the standard.

  EPSON ACULASER M2010DN PDF

This is often sludge from a water treatment plant mixed with a certain percentage of v5511 material from composting facilities.

Specific hazards are given in Section 8. Specific hazards are given in Section 8. The procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions. Ashm Version s – view previous versions of standard. The vessels are airtight and are not exposed to UV radiation.

These gasses are measured daily and the results are carefully recorded. Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test.

ASTM D – Anaerobic Biodegradation | Situ Biosciences LLC

The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. The test asrm are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste.

Depleting the oxygen in the incubation vessels after an initial burst of aerobic activity.

The molar awtm of the total gas produced by the test samples is calculated and compared to the carbon weight of the original samples and the percent biodegradation of the samples can then be determined. The values given in SI units are to be regarded as the standard.

BioPro Global – ASTM D

As these bacteria begin to utilize the carbon in the test samples, they produce carbonaceous axtm such as CO2 and CH4. Biodegradation of a plastic within a high-solids anaerobic digestion unit is an important phenomenon because it will affect the decomposition of other waste materials enclosed by the plastic and the resulting quality and appearance of the digestate after an anaerobic digestion process.

  LM350 DATASHEET PDF

More specifically, the procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This procedure has been developed to permit the determination of the rate and degree of anaerobic biodegradability of plastic products when placed in a high-solids anaerobic digester for the production of digestate from municipal solid waste. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This test method determines the degree and rate of biodegradation of plastic materials in an oxygen-free anaerobic environment. Biodegradation of plastics could allow for the safe disposal of these plastics through aerobic and anaerobic solid-waste-treatment plants.

Link to Active This link will always route to the current Active version of the standard.

However, it is expected to resemble the environment of a high-solids anaerobic-digestion process operated under optimum conditions. When the test is run to satisfaction, final satm and methane gas readings are recorded and the incubation vessels are emptied and the samples are cleaned and weighed. Furthermore, results shall not be extrapolated past the actual duration of the test.