Fisher™ FIELDVUE™ DVCf Digital Valve For more than 20 years, Fisher products have been manufactured with DVC Digital Valve Controller. Fisher r. FIELDVUE™ DVC Digital Valve. Controllers. Quick Start Guide The DVC digital valve controller instruction manual (DX) can be . Note. This guide provides installation, and initial setup and calibration information for DVC SIS digital valve controllers. The following documents are also.

Author: Memi Ditilar
Country: Pacific Islands
Language: English (Spanish)
Genre: Spiritual
Published (Last): 10 September 2005
Pages: 322
PDF File Size: 13.92 Mb
ePub File Size: 14.43 Mb
ISBN: 569-8-14558-984-4
Downloads: 15942
Price: Free* [*Free Regsitration Required]
Uploader: Mikakus

Select Yes to adjust the relay.

By pressing ‘print’ button you will print only current page. Maintenance and Troubleshooting 0. If using natural gas as the plastic cover when flammable gases pneumatic supply medium, natural gas will be used in or dust are present, do not rub or the pneumatic output connections of the DVC to fishe the cover with solvents. Page of Go. Place the instrument In Service and verify that the calibrated.

Remote Travel Sensor Connections 4. Supply Press Alrt Alert Record! Don’t show me this message again. Maximum Cable Capacitance Burst cable length, select a wire with lower capacitance per Command 3. Device Revision Crossover Point Revision number of the interface software that The point at which the feedback pin is closest to permits communication between the Field the axis of rotation of the travel sensor.


Fisher DVC6000 – Digital Smart Positioner

Valve signature test — Test benchmarks valve operation by determining spring rate, seating forces, friction and bench set.

Drive Alrt Enab 5. Output Connections Installation Output Connections A factory mounted digital valve controller has its output piped to the pneumatic input connection on the actuator.

Check mounting and feedback arm adjustments, and inst supply pressure. Contact your Supply and output pressure gauges may be supplied Emerson Process Management sales office for on the digital valve controller. All other marks are the property of their respective owners. Where a key number is referenced, figure Proc anagement Process Management.

Some of the procedures also contain the sequence of Check the control mode using the Field Communicator. As with most industrial process operations, the safety risk to personnel, equipment and the environment in case of an emergency is ever-present. Cycl Count Airt Pt 3.

Tvl Limit Low 3. Installations on connector arm and loosely install the flanged hex nut. Page 15 Introduction and Specifications Table Aux In Airt State 3.


Supported products may not be manufactured again fisger any Emerson Process Management location under any. This dangerously prevents the SIS from performing the way it is designed. Connect the second wire of the 3-conductor Position the adjustment arm in the slot of the inches from roller to pivot point].

Auto Calib Travel 5. Man Calib Travel 5. Evenly svc6000 the screws in a crisscross pattern to a final torque of 16 NSm lbfSin. Attach the travel indicator, to the shaft connector or spacer as described in the mounting kit instructions. Auto Calib Travel 3.

  EN 61779-1 PDF

Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance. Utility 1 2.

Fisher DVC – Digital Smart Positioner

Page 19 Introduction and Specifications Table Conventions Used in this Manual. If not already installed, press three retaining rings key into the module base. Calibration Location Algorithm Where the instrument was last calibrated; either A set of logical steps to solve a problem or in the factory or in the field. Sliding-Stem Control Valve with cautions and warnings. Critical NUM Fail 5. The Performance Tuner is used to optimize digital valve controller tuning.

If there is an output pressure deviation, for example, the instrument will issue an alert. Polling Address Measured Var! If the DVC D Svc6000 bypass valves or completely is installed in an area where the exterior surfaces tend shut off the process to isolate the valve to get heavily coated or layered with industrial or